Samson 1400 Istruzioni per gli Interventi Pagina 46
- Pagina / 72
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
P7 *
w/x
>> /<> [>>]
Direction of action of the reference variable w to the travel/rotational
angle x (increasing/increasing or increasing/decreasing).
P8
Gain K
P
30/[50]
On initializing the positioner, the gain is set to the selected value.
P9 *
Pressure limit
ON/[OFF]
The signal pressure can take on the same pressure as the supply air
at the maximum [OFF] or, in the case that the maximum actuator
force can damage the valve, the pressure is limited to approx.
2.4 bar.
P10 *
End position w <
[ON]/OFF
Tight-closing function:
If w reaches up to 1 % towards the final value that causes the valve to
close, the actuator is immediately completely vented (with
ATO - Air
to open) or filled with air (with
ATC - Air to close).
This action always lead to maximum tight-closing of the valve.
P11 *
End position w >
ON/ [OFF]
Tight-closing function:
If w reaches up to 99 % towards the final value that causes the valve
to open, the actuator is immediately completely filled with air (with
ATO - Air to open) or vented (with ATC - Air to close).
This action always lead to the valve being completely opened.
P12 *
Switching point A1
0 to 100 % [2 %]
Software limit value A1 is displayed or can be changed in relation to
the operating range (steps of 0.5 %).
P13 *
Switching point A2
0 to 100 % [98 %]
Software limit value A2 is displayed or can be changed in relation to
the operating range (steps of 0.5 %).
P14
Info w/Man w Display only, indicates the reference variable applied in 0 to 100 %
corresponding 4 to 20 mA.
Manual adjustment, refer to section 7.9.
P15
Start
initialization
The initialization process can be interrupted by pressing the rotary
pushbutton. The control valve moves to its fail-safe position.
Over parameter code
P0, the fail-safe position can be canceled
again and the positioner then starts with the original setting.
Also after a power supply failure, the positioner starts with its orig
-
inal setting.
P16 *
Start
zero calibration
The zero calibration process can be interrupted by pressing the ro
-
tary pushbutton. The control valve moves to its fail-safe position.
Over parameter code
P0, the fail-safe position can be canceled
again and the positioner then starts with the original setting.
Also after a power supply failure, the positioner starts with its
original setting.
46 EB 8384-1 EN
Code list
- Mounting and 1
- Operating Instructions 1
- EB 8384-1 EN (1300-1610) 1
- EB 8384-1 EN 2
- EB 8384-1 EN 3 3
- 4 EB 8384-1 EN 4
- EB 8384-1 EN 5 5
- Vent opening 6
- 2 Article code 7
- 3 Design and principle of 8
- 3.1 Technical data 10
- 4 Attachment to the control 12
- 4.1 Direct attachment 14
- 4.1.1 Type 3277-5 Actuator 14
- 4.1.2 Type 3277 Actuator 16
- IEC 60534-6 18
- 4.2 Attachment according to 18
- 4.3 Attachment according to 20
- VDI/VDE 3847 20
- 4.4 Attachment to Type 3510 20
- Micro-flow Valve 20
- 4.5 Attachment to rotary 22
- 4.5.1 Heavy-duty version 24
- 4.6 Reversing amplifier for 26
- 4.6.1 Reversing amplifier 26
- (1079-1118 or 1079-1119) 26
- From the positioner 27
- Control signals to 27
- 4.8 Air purging function for 28
- 4.9 Mounting parts and 29
- 32 EB 8384-1 EN 32
- 5 Connections 33
- 5.1 Pneumatic connections 33
- 5.1.1 Signal pressure gauges 34
- 5.1.2 Supply pressure 34
- 5.2 Electrical connections 35
- 5.2.1 Switching amplifier 37
- 6 Operation 38
- 6.1 Operator controls 38
- 7 Start-up 39
- 7.2 Adapting the display 40
- 7.3 Entering the opening 40
- 7.4 Setting other parameters 41
- 7.5 Initialization 41
- Initialization successfully 42
- 7.6 Faults 43
- 7.7 Zero calibration 43
- 7.8 Reset 44
- 7.9 Manual adjustment 44
- 8 Code list 45
- 46 EB 8384-1 EN 46
- Code list 46
- 48 EB 8384-1 EN 48
- 9 Maintenance 49
- 50 EB 8384-1 EN 50
- 11 Dimensions in mm 51
- Dimensions in mm 52
- 52 EB 8384-1 EN 52
- 54 EB 8384-1 EN 54
- EB 8384-1 EN 55 55
- 56 EB 8384-1 EN 56
- EB 8384-1 EN 57 57
- 58 EB 8384-1 EN 58
- EB 8384-1 EN 59 59
- 60 EB 8384-1 EN 60
- EB 8384-1 EN 61 61
- 62 EB 8384-1 EN 62
- EB 8384-1 EN 63 63
- 64 EB 8384-1 EN 64
- EB 8384-1 EN 65 65
- 66 EB 8384-1 EN 66
- Model 3730-13 67
- UNSPECIFIED APPARATUS 67
- 68 EB 8384-1 EN 68
- 70 EB 8384-1 EN 70
- EB 8384-1 EN 71 71
Prodotti e manuali riguardandi Amplificatori audio Samson 1400
Amplificatori audio Samson 1400 Manuale Utente
(12 pagine)
(12 pagine)
Amplificatori audio Samson 1200 Specifiche
(60 pagine)
(60 pagine)
Amplificatori audio Samson B Series B900 Manuale
(60 pagine)
(60 pagine)
Amplificatori audio Samson Cque 8 Manuale Utente
(24 pagine)
(24 pagine)
Amplificatori audio Samson SCOM Specifiche
(67 pagine)
(67 pagine)
(5 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale