Samson S2000 Specifiche Pagina 8

  • Scaricare
  • Aggiungi ai miei manuali
  • Stampa
  • Pagina
    / 12
  • Indice
  • SEGNALIBRI
  • Valutato. / 5. Basato su recensioni clienti
Vedere la pagina 7
6
The S1500 / S2000 Protection Circuitry
As noted in the Guided Tour section of this manual, the S1500 / S2000 front-
panel Protection LED indicates the activity of the relay speaker connection
circuitry. When the Protection LED is lit, this circuitry is active, and all connected
speakers are muted (provided with 0 volts DC), thus protecting them and
preventing any audible thump from occurring.
The following conditions will cause the Protection LED to go on:
Initial power-up: For approximately five seconds after initial power-up, the
protection circuitry is activated and the speaker output is muted. If everything is
operating normally, you will hear an audible click at the conclusion of this brief
period, as the protection circuitry is deactivated and the S1500 / S2000 begins
delivering signal to connected speakers (at which point youll hear a click). It is
normal for the Protection LED to fade gradually after the amplifier is powered off.
Overheating: A temperature sensing device in the S1500 / S2000 will cause
the protection circuitry to be activated (and the Protection LED to go on)
whenever the operating temperature of the unit rises above a safe level. To
guard against this problem, make sure the S1500 / S2000 receives adequate
ventilation on all sides and that both the front and rear panels are unobstructed.
Severe overcurrent conditions: This occurs whenever the signal being input to
the S1500 / S2000 rises to a level above 20% THD (Total Harmonic Distortion).
Shorted speaker cables: This will occur if, due to faulty wiring, the hot and
ground signals being output by the S1500 / S2000 short one another.
Output impedance drops below 2 ohms: This can occur if the S1500 / S2000
is connected to inappropriate speaker systems (see the Setting Up and Using
Your S1500 / S2000 section on page 5 in this manual for more information).
DC voltage detected at speaker output: The most likely cause of this is an
internal failure.
In general, any time the Protection LED lights up (other than during the
approximately five seconds following initial power-up), there is reason to be
concerned. If this occurs, turn the S1500 / S2000 off immediately and carefully
check all wiring and external devices in order to locate and correct the condition
that caused the LED to light up in the first place.
For further assistance, contact your local Samson dealer. If purchased in the
United States, you can call Samson Technical Support (1-800-372-6766)
between 9 AM and 5 PM EST.
WARNING: If the Protection LED fails to go out (and you fail to hear the
accompanying audible click) approximately five seconds after power-up,
turn the S1500 / S2000 off immediately and check all external devices and
wiring for possible shorts or other defects.
PROTECTION
Vedere la pagina 7
1 2 3 4 5 6 7 8 9 10 11 12

Commenti su questo manuale

Nessun commento

Harbor Freight Tools 2 ton Manual Chain Hoist manuales

Manuales del propietario y guías del usuario para No Harbor Freight Tools 2 ton Manual Chain Hoist.
Ofrecemos 1 manuales en pdf Harbor Freight Tools 2 ton Manual Chain Hoist para descargar gratis por tipos de documentos: Manual






Más productos y manuales para No Harbor Freight Tools

Modelos Tipo de documento
40 ft. Retractable Cord Reel with Triple Tap Manual   Harbor Freight Tools 40 ft. Retractable Cord Reel with Triple Tap Product manual, 4 paginas
Solar Power Connection Cable Kit Manual   Harbor Freight Tools Solar Power Connection Cable Kit Product manual, 4 paginas
Multi_Use Transfer Pump Manual   Harbor Freight Tools Multi_Use Transfer Pump Product manual, 4 paginas
High Lift Riding Lawn Mower / ATV Lift Manual   Harbor Freight Tools High Lift Riding Lawn Mower / ATV Lift Product manual, 12 paginas
Fluorescent Work Light with 6 ft. Cord Manual   Harbor Freight Tools Fluorescent Work Light with 6 ft. Cord Product manual, 1 paginas
(420cc) Guía de inicio rápido   Harbor Freight Tools (420cc) Quick Start Guide, 2 paginas
1/4 HP Submersible Sump Pump with Vertical Float 2800 GPH Manual   Harbor Freight Tools 1/4 HP Submersible Sump Pump with Vertical Float 2800 GPH Product manual, 9 paginas
44 in. 13 Drawer Glossy Red Industrial Roller Cabinet Manual   Harbor Freight Tools 44 in. 13 Drawer Glossy Red Industrial Roller Cabinet Product manual, 8 paginas
450 lb. Low Lift Transmission Jack Manual   Harbor Freight Tools 450 lb. Low Lift Transmission Jack Product manual, 8 paginas
Quick Change Sanding Drum Set 4 Pc Manual   Harbor Freight Tools Quick Change Sanding Drum Set 4 Pc Product manual, 1 paginas
Mityvac Vacuum Pump Manual     Harbor Freight Tools Mityvac Vacuum Pump Product manual, 76 paginas
96902 Manual de usuario   Harbor Freight Tools 96902 User's Manual, 7 paginas
R134A Guía de inicio rápido   Harbor Freight Tools R134A Quick Start Guide, 4 paginas
Drill Press Extension Table with Fence Manual   Harbor Freight Tools Drill Press Extension Table with Fence Product manual, 9 paginas
2 Pc Flush_Mount Truck Bed Anchors Manual   Harbor Freight Tools 2 Pc Flush_Mount Truck Bed Anchors Product manual, 4 paginas
Bigfoot Panel Wagon Manual   Harbor Freight Tools Bigfoot Panel Wagon Product manual, 4 paginas
3 gal. 1/3 HP 100 PSI Oilless Pancake Air Compressor Guía de inicio rápido   Harbor Freight Tools 3 gal. 1/3 HP 100 PSI Oilless Pancake Air Compressor Quick Start Guide, 2 paginas
45076 Manual de usuario   Harbor Freight Tools 45076 User's Manual, 3 paginas
95799 Manual de usuario   Harbor Freight Tools 95799 User's Manual, 7 paginas
Welding Cabinet Manual   Harbor Freight Tools Welding Cabinet Product manual, 8 paginas